Maple Mac Crack

  

The Maple IDE is based around dfu-util, openMoko’s DFU utility. Using DFU came at a cost, however. The USB port must additionally implement a separate serial port at the same time (we use the CDC ACM class for serial functionality). Maple Rev 1 attempted to run both DFU and CDC ACM devices simultaneously on the USB peripheral. Maple Crack + Mac. Maple 2018 Crack is an efficient program who enables you to use this program for the purpose of resolve the issue of your data analyzing and also provides you the best solution about all the type of mathematical problems, scientific and many others Maple Tool also used in the hands of professionals, engineers etc. Maple Mac Crack 2018 is one of the best and most powerful.

The Blue Pill (STM32) can be bought very cheaply on sites like eBay and Aliexpress, but they likely do not come shipped with a USB bootloader. You are then forced to use a USB to Serial/USB to TTL to interface with the BLue Pill, and that can be a nuisance sometimes, especially since you have to change the BOOT0 pin from 0 to 1 to upload, and then the reverse to run a sketch.

This post will show you how to upload a new bootloader to the Blue Pill and upload sketches over USB with PlatformIO in Windows.

Prerequisites

You will need a few things to get up and running:

  • Blue Pill board
  • USB to Serial/USB to TTL adapter
    • Jumper cables for connecting
  • Micro USB cable
  • USB Maple serial drivers. Clone/download this repo.
  • Proper bootloader

To get the proper bootloader for your Blue Pill, read the pin number for the built-in LED of the board. The following example picture has its LED on pin PC13.

Then nagivate to Roger Clark's STM32duino-bootloader repo and download the appropriate .bin bootloader file that corresponds to your Blue Pill's LED pin. Since the example picture's LED pin is PC13, I would download generic_boot20_pc13.bin.

For the USB Maple serial driver, navigate to the driverswin folder and run the install_drivers.bat batch file. The drivers will automatically install. Approve any Administrator requests.

Preparing the Blue Pill for flashing

Connect the USB to Serial/USB to TTL adapter to your PC and the Blue Pill. The reference pins are:

Adapter PinBlue Pill Pin
3V33.3
GNDGND
TXDA10
RXDA9

Move the jumper on BOOT0 from 0 to 1. Hit the RESET button.

Here's a reference pinout diagram.

Your PC should recognize the USB serial device. To double-check, you can open up Device Manager and looking for the device under 'Ports'.

Flash the bootloader

Open the Demonstrator GUI. Make sure the right COM port is selected.

Select 'Next' The following screen should indicate that the Target is readable. If not, reset the Blue Pill again. Check your connections. Proceed to the next screen, where you'll see the the available pages for flashing. Proceed to the next screen.

Select the Download to Device radio button, and select the proper bootloader .bin file.

Then select 'Next' to flash the bootloader.

Maple

Once done, close out of the program.

IMPORTANT: Before powering off the Blue Pill, return the BOOT0 jumper to 0.

Then you're finished! Disconnect the USB to Serial/USB to TTL adapter, and connect the Blue Pill with a Micro USB cable. You should see the serial device in Device Manager:

Uploading Sketches with PlatformIO

You can create a new PlatformIO project for the Blue Pill by selecting the proper board during project creation:

For a new project or an existing project, ensure you have the proper platformio.ini settings:

The most important entry is upload_protocol = dfu. PlatformIO will attempt to place the Blue Pill in DFU mode to upload the sketch, and then reset it.

If the upload process halts when 'searching for DFU devices', you may need to manually reset the Blue Pill to upload the sketch.

Using PA11 and PA12

PA11 and PA12 are used for USB serial communication. They cannot be immediately used for regular pin interactions like IO, especially the PWM pin on PA11. To enable this functionality, we can disable USB serial by opening usb_serial.cpp found in .platformiopackagesframework-arduinoststm32STM32F1coresmaple

Maple mac crack recipe

Then comment out everything inside void USBSerial::begin(void).

Resetting the Blue Pill via USB will no longer work and will require a manual reset.

Enjoy!

Maple 2020 Mac Crack


Get an edge in your math, engineering & science classes!

Maple is powerful, easy to use math software that can improve your grades, save you time and money, and increase your confidence.

Maple 2021 Mac Crack

In fact, Maple may very well be the most powerful piece of software you will ever use. Maple is used in robotics, aerospace, medical research, green energy projects, consumer electronics, and a whole lot more. Today, Maple will help you succeed in your courses. Tomorrow? Who knows!


Already have Maple? Visit the Student Help Center for lots of great resources

Maple 2020 Mac Crack

Maple is part of the Maple Math Suite. Check out the full range of math education products to find the one that suits you best.